For two decades, Nano-Tech Security Films has specialized in the production of multi-laminate safety and security window films, designed to protect people and properly against flying glass shards.

Tested Tough, Nano-Tech Security Films meets the Most Stringent Standards and Numerous Certifications suitable for a broad range of applications around the world.

Commander
4 Mil

Do you want to protect your family and your home from the average household accident involving broken glass?

Perhaps you know someone who unintentionally walked through a glass door and got hurt, or maybe you had a ball crash through your window pane, narrowly missing you or your child. Eliminate this risk with our Commander 4 MIL Safety Window Film. Designed to be impact resistant, this window film will hold the glass together in the event of a breakage, without obscuring vision. Constructed at 4 millimeters thick, the Commander 4 Mil safety film is not designed for security from break-ins, but it can slow down attempts.

Specs
Test Standard Characteristic Result
16 CPSC 1201 Safety Glazing Impact Resistance Designed to Pass Category I & II
16 CPSC 1201 Safety Glazing Weathering Meets Requirements of Section 1201.4(e) 1(iv) & 2(iv)
ANSI Z97.1 Impact Resistance Designed to Pass Unlimited Requirements
ANSI Z97.1 Weathering Designed to meet Requirements of Section Z97.1.5.3.1
BS 2606 Impact Resistance Designed to Pass All Requirements
ASTM D3330-96 ASTM G26 Peel Adhesion 5.5lbs/in Pre-Weathered
ASTM D1044-94 Surface Abrasion Resistance Delta Haze <3%
ASTM D635-88 Rate of Burning Materal Does Not Stay Ignited Long Enough for Reading
GSA’s Method for Glazing Systems Subject to Air Blast Loading Bomb Blast Mitigation Designed to Perform to GSA
Hazard Level 3 Open Arena

Machete
8 Mil

A deterrent to would-be robbers, protection from the average household accident, and guards against wind borne debris. These are just a few of the features you will receive when installing our Machete 8 Mil Security Window Film.

Designed to hold the glass together in the event that the window is broken or damaged, this film also contains a UV rejection rate of up to 99%. When installed correctly, the Machete 8 Mil security film forces someone trying to break through to expend much more time and energy, just to penetrate it a little bit, that it is more likely they will retreat. In addition to the security, this film has the added benefit of protecting your house and family from everyday accidents; maybe a ball is accidentally thrown at a window, or a large glass door appears open and someone may run through it. Either way, with the added safety a severe injury is much less likely.

Specs
Test Standard Characteristic Result
16 CPSC 1201 Safety Glazing Impact Resistance Designed to Pass Category I & II
16 CPSC 1201 Safety Glazing Weathering Meets Requirements of Section 1201.4(e) 1(iv) & 2(iv)
ANSI Z97.1 Impact Resistance Designed to Pass Unlimited Requirements
ANSI Z97.1 Weathering Designed to meet Requirements of Section Z97.1.5.3.1
BS 2606 Impact Resistance Designed to Pass All Requirements
ASTM D3330-96 ASTM G26 Peel Adhesion 5.5lbs/in Pre-Weathered
ASTM D1044-94 Surface Abrasion Resistance Delta Haze <3%
ASTM D635-88 Rate of Burning Materal Does Not Stay Ignited Long Enough for Reading
GSA’s Method for Glazing Systems Subject to Air Blast Loading Bomb Blast Mitigation Designed to Perform to GSA
Hazard Level 3 Open Arena
Dade County Small Missile Test Wind Borne Debris Designed to Pass PA201, PA202 and PA203 with Anchoring

All security films are installed on the interior surface of a window. The best method of installation is to remove the glass from the window frame, install the film, and reinstall the glass into the frame. The frame will act as an anchor to the film. If this is not possible, a bead of clear (or white, if preferred) silicone around the edge of the glass, about 24-48 hours after installation, is highly recommended. This will keep the glass and film firmly anchored in the frame if the glass is broken.

Blast Shield
12 MIL

Similar in make-up to our Machete 8 MIL Security Film, the Blast Shield 12 MIL Security Window Film offers the highest protection against robbery attempts, household accident, wind damage, and even some outside explosion safety. This film protects is the entry level for Bomb Attacks.

Because the film is 1 ½ times thicker than the 8 mil, this gives it an added layer of resistance; resulting in an even harder film for burglars to get through and in some cases causing objects will simply bounce off the glass on impact. It’s also designed to hold the glass together, in the event of a breakage. The Blast Shield 12 MIL Security Film is a must have for the home or building safety conscious. 

Specs
Test Standard Characteristic Result
16 CPSC 1201 Safety Glazing Impact Resistance Designed to Pass Category I & II
16 CPSC 1201 Safety Glazing Weathering Meets Requirements of Section 1201.4(e) 1(iv) & 2(iv)
ANSI Z97.1 Impact Resistance Designed to Pass Unlimited Requirements
ANSI Z97.1 Weathering Designed to meet Requirements of Section Z97.1.5.3.1
BS 2606 Impact Resistance Designed to Pass All Requirements
ASTM D3330-96 ASTM G26 Peel Adhesion 5.5lbs/in Pre-Weathered
ASTM D1044-94 Surface Abrasion Resistance Delta Haze <3%
ASTM D635-88 Rate of Burning Materal Does Not Stay Ignited Long Enough for Reading
GSA’s Method for Glazing Systems Subject to Air Blast Loading Bomb Blast Mitigation Designed to Perform to GSA
Hazard Level 3 Open Arena
Dade County Small Missile Test Wind Borne Debris Designed to Pass PA201, PA202 and PA203 with Anchoring
HPW-TP-0500.02 Ballistics .38 Special On 3/4″ Glass No Penetration-3shots
HPW-TP-0500.02 Ballistics 9mm Special On 3/4″ Glass No Penetration-3shots
HPW-TP-0500.02 Ballistics .38 Special On 1/2″ Glass No Penetration – 2shots
Penetration – 3rd shot

All security films are installed on the interior surface of a window. The best method of installation is to remove the glass from the window frame, install the film, and reinstall the glass into the frame. The frame will act as an anchor to the film. If this is not possible, a bead of clear (or white, if preferred) silicone around the edge of the glass, about 24-48 hours after installation, is highly recommended. This will keep the glass and film firmly anchored in the frame if the glass is broken.

Blast Shield
16 MIL

Exceptional performance. Maximum protection for the glass windows against large scale explosives. Integrating with an attachment system offers the highest level of protection strong enough to help protect occupants against bomb blasts Creates a robust window protection system that significantly outperforms window film-only installations. The Blast Shield 16 MIL Security Film is a must have for high security risk areas such as government buildings or embassies. 

Specs
Test Standard Characteristic Result
16 CPSC 1201 Safety Glazing Impact Resistance Designed to Pass Category I & II
16 CPSC 1201 Safety Glazing Weathering Meets Requirements of Section 1201.4(e) 1(iv) & 2(iv)
ANSI Z97.1 Impact Resistance Designed to Pass Unlimited Requirements
ANSI Z97.1 Weathering Designed to meet Requirements of Section Z97.1.5.3.1
BS 2606 Impact Resistance Designed to Pass All Requirements
ASTM D3330-96 ASTM G26 Peel Adhesion 5.5lbs/in Pre-Weathered
ASTM D1044-94 Surface Abrasion Resistance Delta Haze <3%
ASTM D635-88 Rate of Burning Materal Does Not Stay Ignited Long Enough for Reading
GSA’s Method for Glazing Systems Subject to Air Blast Loading Bomb Blast Mitigation Designed to Perform to GSA
Hazard Level 3 Open Arena
Dade County Small Missile Test Wind Borne Debris Designed to Pass PA201, PA202 and PA203 with Anchoring
HPW-TP-0500.02 Ballistics .38 Special On 3/4″ Glass No Penetration-3shots
HPW-TP-0500.02 Ballistics 9mm Special On 3/4″ Glass No Penetration-3shots
HPW-TP-0500.02 Ballistics .38 Special On 1/2″ Glass No Penetration – 2shots
Penetration – 3rd shot

All security films are installed on the interior surface of a window. The best method of installation is to remove the glass from the window frame, install the film, and reinstall the glass into the frame. The frame will act as an anchor to the film. If this is not possible, a bead of clear (or white, if preferred) silicone around the edge of the glass, about 24-48 hours after installation, is highly recommended. This will keep the glass and film firmly anchored in the frame if the glass is broken.